In London, in 1946, 65 delegates from 25 countries meet to discuss the future of International Standardization. In 1947, ISO officially comes into existence with 67 technical committees (groups of experts focusing on a specific subject).
ISO is an independent, non-governmental international organization with a membership of 165 national standards bodies.
Through its members, it brings together experts to share knowledge and develop voluntary, consensus-based, market relevant International Standards that support innovation and provide solutions to global challenges.
Below list including all current fastener standards in ISO Standards.
| ISO 68-1 – ISO GENERAL PURPOSE SCREW THREADS – BASIC PROFILE – PART 1: METRIC SCREW THREADS | |
| ISO 68-2 – ISO GENERAL PURPOSE SCREW THREADS – BASIC PROFILE – PART 2: INCH SCREW THREADS | |
| ISO 225 – Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions | |
| ISO 261 – ISO General Purpose Metric Screw Threads – General Plan | |
| ISO 262 – ISO General Purpose Metric Screw Threads – Selected Sizes for Screws, Bolts and Nuts | |
| ISO 263 – ISO Inch Screw Threads – General Plan and Selection for Screws, Bolts and Nuts – Diameter Range 0,06 to 6 in | |
| ISO 272 – Fasteners – Hexagon Products – Widths Across Flats | |
| ISO 273 – Fasteners – Clearance Holes for Bolts and Screws | |
| ISO 299 – Machine Tool Tables – T-Slots and Corresponding Bolts | |
| ISO 691 – Assembly Tools for Screws and Nuts – Wrench and Socket Openings – Tolerances for General Use | |
| ISO 724 – ISO GENERAL-PURPOSE METRIC SCREW THREADS – BASIC DIMENSIONS | |
| ISO 725 – ISO inch screw threads — Basic dimensions | |
| ISO 885 – General Purpose Bolts and Screws – Metric Series – Radii under the Head | |
| ISO 887 – Plain Washers for Metric Bolts, Screws and Nuts for General Purposes – General Plan | |
| ISO 888 – Fasteners – Bolts, screws and studs – Nominal lengths and thread lengths | |
| ISO 898-1 – Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes – Coarse thread and fine pitch thread | |
| ISO 898-2 – Mechanical properties of fasteners made of carbon steel and alloy steel – Part 2: Nuts with specified property classes – Coarse thread and fine pitch thread | |
| ISO 898-3 – MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL – PART 3: FLAT WASHERS WITH SPECIFIED PROPERTY CLASSES | |
| ISO 898-5 – Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread | |
| ISO 898-7 – Mechanical Properties of Fasteners – Part 7: Torsional Test and Minimum Torques for Bolts and Screws with Nominal Diameters 1 mm to 10 mm | |
| ISO 965-1 – ISO GENERAL PURPOSE METRIC SCREW THREADS – TOLERANCES – PART 1: PRINCIPLES AND BASIC DATA | |
| ISO 965-2 – ISO GENERAL PURPOSE METRIC SCREW THREADS – TOLERANCES – PART 2: LIMITS OF SIZES FOR GENERAL PURPOSE EXTERNAL AND INTERNAL SCREW THREADS – MEDIUM QUALITY | |
| ISO 965-3 – ISO GENERAL PURPOSE METRIC SCREW THREADS – TOLERANCES – PART 3: LIMIT DEVIATIONS FOR SCREW THREADS | |
| ISO 965-4 – ISO General Purpose Metric Screw Threads – Tolerances – Part 4: Limits of Sizes for Hot-Dip Galvanized External Screw Threads to Mate with Internal Screw Threads Tapped with Tolerance Position H or G After Galvanizing | |
| ISO 965-5 – ISO GENERAL PURPOSE METRIC SCREW THREADS – TOLERANCES – PART 5: LIMITS OF SIZES FOR INTERNAL SCREW THREADS TO MATE WITH HOT-DIP GALVANIZED EXTERNAL SCREW THREADS WITH MAXIMUM SIZE OF TOLERANCE POSITION H BEFORE GALVANIZING | |
| ISO 1085 – Assembly tools for screws and nuts – Double-ended wrenches – Size pairing | |
| ISO 1173 – Assembly Tools for Screws and Nuts – Drive Ends for Hand- and Machine-Operated Screwdriver Bits and Connecting Parts – Dimensions, Torque Testing | |
| ISO 1174-1 – Assembly Tools for Screws and Nuts – Driving Squares – Part 1: Driving Squares for Hand Socket Tools | |
| ISO 1174-2 – Assembly Tools for Screws and Nuts – Driving Squares – Part 2: Driving Squares for Power Socket Tools | |
| ISO 1179-1 – Connections for general use and fluid power – Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing – Part 1: Threaded ports | |
| ISO 1179-2 – Connections for general use and fluid power – Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing – Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) | |
| ISO 1179-3 – Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing — Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) | |
| ISO 1179-4 – Connections for general use and fluid power – Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing – Part 4: Stud ends for general use only with metal-to-metal sealing (type B) | |
| ISO 1207 – Slotted cheese head screws — Product grade A | |
| ISO 1461 – Hot dip galvanized coatings on fabricated iron and steel articles – Specifications and test methods | |
| ISO 1478 – Tapping Screws Thread | |
| ISO 1479 – Hexagon head tapping screws | |
| ISO 1481 – Slotted pan head tapping screws | |
| ISO 1482 – Slotted countersunk (flat) head tapping screws | |
| ISO 1483 – Slotted raised countersunk (oval) head tapping screws | |
| ISO 1501 – ISO MINIATURE SCREW THREADS | |
| ISO 1502 – ISO General-Purpose Metric Screw Threads – Gauges and Gauging | |
| ISO 1580 – Slotted pan head screws – Product grade A | |
| ISO 1703 – Assembly tools for screws and nuts – Nomenclature | |
| ISO 1704 – Ships and marine technology — Stud-link anchor chains | |
| ISO 1711-1 – Assembly tools for screws and nuts — Technical specifications — Part 1: Hand-operated wrenches and sockets | |
| ISO 1711-2 – Assembly tools for screws and nuts — Technical specifications — Part 2: Machine-operated sockets (impact) | |
| ISO 1891 – Fasteners – Terminology | |
| ISO 1891-2 – FASTENERS – TERMINOLOGY – PART 2: VOCABULARY AND DEFINITIONS FOR COATINGS | |
| ISO 1891-4 – Fasteners – Vocabulary – Part 4: Control, inspection, delivery, acceptance and quality | |
| ISO 2009 – Slotted countersunk flat head screws — Product grade A | |
| ISO 2010 – Slotted raised countersunk head screws — Product grade A | |
| ISO 2236 – Assembly Tools for Screws and Nuts – Forged and Tubular Socket Wrenches – Maximum Outside Head Dimensions | |
| ISO 2306 – Drills for Use Prior to Tapping Screw Threads | |
| ISO 2320 – Fasteners – Prevailing torque steel nuts – Functional properties | |
| ISO 2342 – Slotted headless screws with shank | |
| ISO 2351-1 – Assembly tools for screws and nuts – Machine-operated screwdriver bits – Part 1: Screwdriver bits for slotted head screws | |
| ISO 2351-2 – Assembly Tools for Screws and Nuts – Machine-Operated Screwdriver Bits – Part 2: Screwdriver Bits for Cross-Recessed Head Screws | |
| ISO 2351-3 – Assembly tools for screws and nuts – Machine-operated screwdriver bits – Part 3: Screwdriver bits for hexagon socket screws | |
| ISO 2380-1 – Assembly tools for screws and nuts Screwdrivers for slotted-head screws Part 1: Tips for hand- and machine-operated screwdrivers | |
| ISO 2380-2 – Assembly tools for screws and nuts Screwdrivers for slotted-head screws Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers | |
| ISO 2702 – Heat-treated steel tapping screws — Mechanical properties | |
| ISO 2725-1 – Assembly tools for screws and nuts – Square drive sockets – Part 1: Hand-operated sockets | |
| ISO 2725-2 – Assembly tools for screws and nuts – Square drive sockets – Part 2: Machine-operated sockets (“impact”) | |
| ISO 2725-3 – Assembly tools for screws and nuts — Square drive sockets — Part 3: Machine-operated sockets (“nonimpact”) | |
| ISO 2901 – ISO metric trapezoidal screw threads – Basic and design profiles | |
| ISO 2902 – ISO metric trapezoidal screw threads – General plan | |
| ISO 2903 – ISO metric trapezoidal screw threads – Tolerances | |
| ISO 2904 – ISO metric trapezoidal screw threads — Basic dimensions | |
| ISO 2936 – Assembly Tools for Screws and Nuts – Hexagon Socket Screw Keys | |
| ISO 2936 – Assembly Tools for Screws and Nuts – Hexagon Socket Screw Keys | |
| ISO 2982-1 – Rolling bearings – Accessories – Part 1: Dimensions for adapter sleeve assemblies and withdrawal sleeves | |
| ISO 2982-2 – Rolling bearings – Accessories – Part 2: Dimensions for locknuts and locking devices | |
| ISO 3168 – Aerospace – Nuts, Anchor, Self-Locking, Fixed, Single Lug with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 3185 – Aerospace — Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions | |
| ISO 3186 – Aerospace — Bolts, large bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes 1 250 MPa to 1 800 MPa — Dimensions | |
| ISO 3191 – Aerospace – Nuts, Anchor, Self-Locking, Fixed, Single Lug, Reduced Series, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/ 235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/ 315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/ 425 Degrees Celsius – Dimensions | |
| ISO 3193 – Aerospace — Bolts, normal hexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions | |
| ISO 3202 – Aerospace – Screws, Pan Head, Internal Offset Cruciform Ribbed or Unribbed Drive, Threaded to Head, MJ Threads, Metallic Material, Coated or Uncoated, Strength Classes Less Than or Equal to 1 100 MPa – Dimensions | |
| ISO 3203 – Aerospace – Bolts, Normal Bihexagonal Head, Normal or Pitch Diameter Shank, Long Length MJ Threads, Metallic Material, Coated or Uncoated, Strength Classes Less Than or Equal to 1 100 MPa – Dimensions First Edition | |
| ISO 3209 – Aerospace – Nuts, anchor, self-locking, floating, two lug, with counterbore, with MJ threads, classifications: 1 100 MPa (at ambient temperature)/ 235 °C, 1 100 MPa (at ambient temperature)/315 °C and 1 100 MPa (at ambient temperature)/ 425 °C – Dimensions | |
| ISO 3221 – Aerospace – Nuts, Anchor, Self-Locking, Fixed, 90 Degree Corner, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 3222 – Aerospace – Nuts, Anchor, Self-Locking, Fixed, Closed Corner, Reduced Series, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 3223 – Aerospace – Nuts, Anchor, Self-Locking, Fixed, Two Lug, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 3224 – Aerospace – Nuts, Anchor, Self-Locking, Floating, Single Lug, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 degrees Celsius – Dimensions | |
| ISO 3225 – Aerospace – Nuts, Anchor, Self-Locking, Fixed, Two Lug, Reduced Series, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 3269 – Fasteners – Acceptance inspection | |
| ISO 3315 – Assembly tools for screws and nuts – Driving parts for hand-operated square drive socket wrenches – Dimensions and tests | |
| ISO 3316 – Assembly tools for screws and nuts – Attachments for hand-operated square drive socket wrenches – Dimensions and tests | |
| ISO 3317 – Assembly tools for screws and nuts – Square drive adaptor with hexagon or cylindrical flat drive, for power socket wrenches | |
| ISO 3318 – Assembly tools for screws and nuts – Open-ended wrenches, box wrenches and combination wrenches – Maximum widths of heads | |
| ISO 3408-1 – Ball screws Part 1: Vocabulary and designation | |
| ISO 3408-2 – Ball Screws – Part 2: Nominal Diameters and Nominal Leads – Metric Series | |
| ISO 3408-3 – Ball screws Part 3: Acceptance conditions and acceptance tests | |
| ISO 3408-4 – Ball screws Part 4: Static axial rigidity | |
| ISO 3408-5 – Ball screws Part 5: Static and dynamic axial load ratings and operational life | |
| ISO 3438 – Subland twist drills for holes prior to tapping screw threads | |
| ISO 3506-1 – Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and studs with specified grades and property classes | |
| ISO 3506-2 – Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 2: Nuts with specified grades and property classes | |
| ISO 3506-3 – Mechanical properties of corrosion-resistant stainless steel fasteners – Part 3: Set screws and similar fasteners not under tensile stress | |
| ISO 3506-4 – Mechanical properties of corrosion-resistant stainless steel fasteners – Part 4: Tapping screws | |
| ISO 3506-6 – Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 6: General rules for the selection of stainless steels and nickel alloys for fasteners | |
| ISO 3508 – Thread Run-Outs for Fasteners with Thread in Accordance with ISO 261 and ISO 262 | |
| ISO 3669 – Vacuum technology — Dimensions of knife-edge flanges | |
| ISO 3800 – Threaded Fasteners – Axial Load Fatigue Testing – Test Methods and Evaluation of Results | |
| ISO 4014 – Hexagon head bolts – Product grades A and B | |
| ISO 4015 – Hexagon Head Bolts – Product Grade B – Reduced Shank (Shank Diameter is Approximately Equal to Pitch Diameter) First Edition | |
| ISO 4016 – Hexagon head bolts — Product grade C | |
| ISO 4017 – Fasteners – Hexagon head screws – Product grades A and B | |
| ISO 4018 – Hexagon head screws – Product grade C | |
| ISO 4026 – Hexagon socket set screws with flat point | |
| ISO 4027 – Hexagon Socket Set Screws with Cone Point | |
| ISO 4028 – Hexagon Socket Set Screws with Dog Point | |
| ISO 4029 – Hexagon socket set screws with cup point | |
| ISO 4032 – Hexagon regular nuts (style 1) – Product grades A and B | |
| ISO 4033 – Hexagon high nuts (style 2) – Product grades A and B | |
| ISO 4034 – Hexagon regular nuts (style 1) – Product grade C | |
| ISO 4035 – Hexagon thin nuts chamfered (style 0) – Product grades A and B | |
| ISO 4042 – Fasteners – Electroplated coating systems | |
| ISO 4147 – Aerospace – Nuts, Hexagonal, Slotted (Castellated), Nrml Ht, Nrml Across Flats, with MJ Threads, Cls: 600MPa (at Ambt T)/120 Dgs C, 600MPa (at Ambt T)/235 Dgs. C, 900MPa (at Ambt T)/425 Dgs. C, 1100 MPa (at Ambt T)/235 Dgs. C, 1100 MPa (at Ambt T)/315 Dgs. C, 1100MPa (at Ambt T)/650 Dgs. C, 1210MPa (at Ambt T)/730 Dgs. C, 1250MPa (at Ambt T)/235 Dgs. C and 1550MPa (at Ambt T)/600 Dgs C – Dims. | |
| ISO 4161 – Hexagon nuts with flange, style 2 – Coarse thread | |
| ISO 4162 – Hexagon bolts with flange – Small series – Product grade A with driving feature of product grade B | |
| ISO 4229 – Assembly tools for screws and nuts – Single-head engineer’s wrenches for lower torque applications – Maximum outside dimensions of heads and test torques | |
| ISO 4753 – Fasteners — Ends of parts with external ISO metric thread | |
| ISO 4755 – Fasteners – Thread Undercuts for External Metric ISO Threads | |
| ISO 4757 – Cross Recesses for Screws | |
| ISO 4759-1 – Tolerances for Fasteners – Part 1: Bolts, Screws Studs and Nuts – Product Grades A, B and C | |
| ISO 4759-3 – Tolerances for fasteners – Part 3: Washers for bolts, screws and nuts – Product grades A, C and F | |
| ISO 4762 – Hexagon socket head cap screws | |
| ISO 4762 – Hexagon socket head cap screws | |
| ISO 4766 – Slotted set screws with flat point | |
| ISO 5393 – Rotary tools for threaded fasteners – Performance test method | |
| ISO 5408 – Screw threads – Vocabulary | |
| ISO 5843-3 – Aerospace – List of Equivalent Terms – Part 3: Aerospace Bolts and Nuts | |
| ISO 5843-3 – Aerospace – List of Equivalent Terms – Part 3: Aerospace Bolts and Nuts | |
| ISO 5845-1 – Technical Drawings – Simplified Representation of the Assembly of Parts with Fasteners – Part 1: General Principles First Edition | |
| ISO 5845-2 – Technical Drawings – Simplified Representation of the Assembly of Parts with Fasteners – Part 2: Rivets for Aerospace Equipment First Edition | |
| ISO 5855-1 – Aerospace – MJ Threads – Part 1: General Requirements | |
| ISO 5855-2 – Aerospace – MJ Threads – Part 2: Limit Dimensions for Bolts and Nuts | |
| ISO 5855-2 – Aerospace – MJ Threads – Part 2: Limit Dimensions for Bolts and Nuts | |
| ISO 5856 – Aerospace – Screws, 100 degrees normal countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa – Dimensions | |
| ISO 5857 – Aerospace — Bolts, with MJ threads, made of alloy steel, strength class 1 250 MPa — Procurement specification | |
| ISO 5858 – Aerospace – Nuts, Self-Locking, with Maximum Operating Temperature Less Than or Equal to 425 Degrees Celsius – Procurement Specification | |
| ISO 5864 – ISO Inch Screw Threads – Allowances and Tolerances | |
| ISO 6157-1 – Fasteners – Surface Discontinuities – Part 1: Bolts, Screws and Studs for General Requirements | |
| ISO 6157-2 – Fasteners – Surface Discontinuities – Part 2: Nuts | |
| ISO 6157-3 – Fasteners – Surface Discontinuities – Part 3: Bolts, Screws and Studs for Special Requirements | |
| ISO 6305-4 – Railway Components – Technical Delivery Requirements – Part 4: Untreated Steel Nuts and Bolts and High-Strength Nuts and Bolts for Fish-Plate and Fastenings First Edition | |
| ISO 6305-4 – Railway Components – Technical Delivery Requirements – Part 4: Untreated Steel Nuts and Bolts and High-Strength Nuts and Bolts for Fish-Plate and Fastenings First Edition | |
| ISO 6410-1 – Technical Drawings – Screw Threads and Threaded Parts – Part 1: General Conventions | |
| ISO 6410-2 – Technical Drawings – Screw Threads and Threaded Parts – Part 2: Screw Thread Inserts | |
| ISO 6410-3 – Technical drawings — Screw threads and threaded parts — Part 3: Simplified representation | |
| ISO 6787 – Assembly Tools for Screws and Nuts – Adjustable Wrenches | |
| ISO 6788 – Assembly Tools for Screws and Nuts – Four-Way Socket Wrenches – Dimensions and Torque Test | |
| ISO 6789-1 – Assembly tools for screws and nuts – Hand torque tools – Part 1: Requirements and methods for design conformance testing and quality conformance testing: minimum requirements for declaration of conformance | |
| ISO 6789-2 – Assembly tools for screws and nuts – Hand torque tools – Part 2: Requirements for calibration and determination of measurement uncertainty | |
| ISO 6891 – Timber Structures – Joints Made with Mechanical Fasteners – General Principles for the Determination of Strength and Deformation Characteristics First Edition | |
| ISO 7040 – Prevailing torque type hexagon regular nuts (with non-metallic insert) – Property classes 5, 8 and 10 | |
| ISO 7041 – Prevailing torque type hexagon nuts (with non-metallic insert), style 2 – Property classes 9 and 12 | |
| ISO 7042 – Prevailing torque type all-metal hexagon high nuts – Property classes 5, 8, 10 and 12 | |
| ISO 7043 – Prevailing torque type hexagon nuts with flange (with non-metallic insert), style 2 – Product grades A and B | |
| ISO 7044 – Prevailing torque type all-metal hexagon nuts with flange, style 2 – Product grades A and B | |
| ISO 7045 – Pan head screws with type H or type Z cross recess — Product grade A | |
| ISO 7046-1 – Countersunk flat head screws (common head style) with type H or type Z cross recess — Product grade A — Part 1: Steel screws of property class 4.8 | |
| ISO 7046-2 – Countersunk flat head screws (common head style) with type H or type Z cross recess — Product grade A — Part 2: Steel screws of property class 8.8, stainless steel screws and non-ferrous metal screws | |
| ISO 7047 – Raised countersunk head screws (common head style) with type H or type Z cross recess — Product grade A | |
| ISO 7048 – Cross-recessed cheese head screws | |
| ISO 7049 – Cross-recessed pan head tapping screws | |
| ISO 7050 – Cross-recessed countersunk (flat) head tapping screws | |
| ISO 7051 – Cross-recessed raised countersunk (oval) head tapping screws | |
| ISO 7053 – Fasteners — Hexagon washer head tapping screws | |
| ISO 7089 – Plain Washers – Normal Series – Product Grade A | |
| ISO 7090 – Plain Washers, Chamfered – Normal Series – Product Grade A | |
| ISO 7091 – Plain Washers – Normal Series – Product Grade C | |
| ISO 7092 – Plain Washers – Small Series – Product Grade A | |
| ISO 7093-1 – Plain Washers – Large Series – Part 1: Product Grade A | |
| ISO 7093-2 – Plain Washers – Large Series – Part 2: Product Grade C | |
| ISO 7094 – PLAIN WASHERS – EXTRA LARGE SERIES – PRODUCT GRADE C | |
| ISO 7332 – Aerospace – Nuts, Anchor, Self-Locking, Floating, Two Lug, Reduced Series, with Counterbore, with MJ Threads, ClassificationS: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 7378 – Fasteners – Bolts, Screws and Studs – Split Pin Holes and Wire Holes | |
| ISO 7379 – Hexagon Socket Head Shoulder Screws | |
| ISO 7380-1 – Button head screws — Part 1: Hexagon socket button head screws | |
| ISO 7380-2 – Button head screws — Part 2: Hexagon socket button head screws with collar | |
| ISO 7434 – Slotted Set Screws with Cone Point | |
| ISO 7435 – Slotted Set Screws with Long Dog Point First Edition; (NZS/ISO 7435: 1983) | |
| ISO 7436 – Slotted Set Screws with Cup Point | |
| ISO 7481 – Aerospace – Nuts, Self-Locking, with Maximum Operating Temperature Less Than or Equal to 425 Degrees Celsius – Test Methods | |
| ISO 7689 – Aerospace — Bolts, with MJ threads, made of alloy steel, strength class 1 100 MPa — Procurement specification | |
| ISO 7719 – Prevailing torque type all-metal hexagon regular nuts – Property classes 5, 8 and 10 | |
| ISO 7720 – Prevailing torque type all-metal hexagon nuts, style 2 – Property class 9 | |
| ISO 7721 – Countersunk Head Screws – Head Configuration and Gauging First Edition | |
| ISO 7721-2 – Countersunk Flat Head Screws – Part 2: Penetration Depth of Cross Recesses | |
| ISO 7738 – Assembly tools for screws and nuts – Combination wrenches – Lengths of wrenches and maximum thickness of heads | |
| ISO 7913 – Aerospace – Bolts and Screws, Metric – Tolerances of Form and Position Second Edition | |
| ISO 7961 – Aerospace — Bolts — Test methods | |
| ISO 7995 – Aerospace – Nuts, Hexagonal, Self-Locking, with MJ Threads, Classification 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa(at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 8168 – Aerospace – Bolts, with MJ threads, made of heat and corrosion resisting steel, strength class 1 100 MPa – Procurement specification | |
| ISO 8279 – Aerospace – Nuts, hexagonal, plain, normal height, normal across flats, with MJ threads, classifications: 600 MPa (at ambient temperature)/120 °C, 600 MPa (at ambient temperature)/235 °C, 900 MPa (at ambient temperature)/425 °C, 1 100 MPa (at ambient temperature)/235 °C, 1 100 MPa (at ambient temperature)/315 °C, 1 100 MPa (at ambient temperature)/650 °C, 1 210 MPa (at ambient temperature)/730 °C, 1 250 MPa (at ambient temperature)/235 °C and 1 550 MPa (at ambient temperature)/600 °C – Dimensions | |
| ISO 8319-1 – Orthopaedic Instruments – Drive Connections – Part 1: Keys for Use with Screws with Hexagon Socket Heads | |
| ISO 8319-2 – Orthopaedic Instruments – Drive Connections – Part 2: Screwdrivers for Single Slot Head Screws, Screws with Cruciate Slot and Cross-Recessed Head Screws | |
| ISO 8538 – Aerospace – Nuts, Hexagonal, Self-Locking with Counterbore and Captive Washer, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 8641 – Aerospace — Self-locking nuts with maximum operating temperature greater than 425 °C — Procurement specification | |
| ISO 8642 – Aerospace — Self-locking nuts with maximum operating temperature greater than 425 Degrees Celsius — Test methods | |
| ISO 8673 – Hexagon regular nuts (style 1) with metric fine pitch thread – Product grades A and B | |
| ISO 8674 – Hexagon high nuts (style 2) with metric fine pitch thread – Product grades A and B | |
| ISO 8675 – Hexagon thin nuts chamfered (style 0) with metric fine pitch thread – Product grades A and B | |
| ISO 8676 – Hexagon head screws with metric fine pitch thread — Product grades A and B | |
| ISO 8678 – Cup Head Square Neck Bolts with Small Head and Short Neck – Product Grade B | |
| ISO 8738 – Plain Washers for Clevis Pins – Product Grade A | |
| ISO 8764-1 – Assembly tools for screws and nuts Screwdrivers for cross-recessed head screws Part 1: Driver tips | |
| ISO 8764-2 – Assembly tools for screws and nuts Screwdrivers for cross-recessed head screws Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers | |
| ISO 8765 – Hexagon head bolts with metric fine pitch thread — Product grades A and B | |
| ISO 8788 – Aerospace — Nuts, metric — Tolerances of form and position | |
| ISO 8940 – Aerospace – Nuts, Anchor, Self-Locking, Sealing, Floating, Two-Lug, with Counterbore with MJ Threads, Classifications 900 MPa (at Ambient Temperature)/ 120 Degrees Celsius, 900 MPa (at Ambient Temperature)/175 Degrees Celsius and 900 MPa (at Ambient Temperature)/235 Degrees Celsius Dimensions | |
| ISO 8969 – Timber structures — Testing of punched metal plate fasteners and joints | |
| ISO 8970 – Timber structures — Testing of joints made with mechanical fasteners — Requirements for timber density | |
| ISO 8991 – Designation System for Fasteners | |
| ISO 8992 – Fasteners General requirements for bolts, screws, studs and nuts | |
| ISO 9139 – Aerospace – Nuts, Plain or Slotted (Castellated) – Procurement Specification | |
| ISO 9140 – Aerospace – Nuts, Plain or Slotted (Castellated) – Test Methods | |
| ISO 9152 – Aerospace – Bolts, with MJ Threads, in Titanium Alloys, Strength Class 1 100 MPa – Procurement Specification | |
| ISO 9154 – Aerospace – Bolts, with MJ threads, made of heat-resistant nickel-based alloy, strength class 1 550 MPa – Procurement specification | |
| ISO 9156 – Aerospace – Nuts, Anchor, Self-Locking, Fixed, 90 Degree Corner, Reduced Series, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius – Dimensions | |
| ISO 9157 – Aerospace – Nuts, Spline-Drive, Self-Locking, with MJ Threads, Classifications: 1 100 MPa (at Ambient Temperature)/425 Degrees C, 1 100 MPa (at Ambient Temperature)/650 Degrees C, 1 210 MPa (at Ambient Temperature)/425 Degrees C, 1 210 MPa (at Ambient Temperature)/730 Degrees C, 1 550 MPa (at Ambient Temperature)/235 Degrees C, 1 550 MPa (at Ambient Temperature)/425 Degrees | |
| ISO 9199 – Aerospace – Nuts, Bihexagonal, Self-Locking, MJ Threads, Classifications 1 100 MPa (at Ambient Temp.)/425 Degrees C, 1 100 MPa (at Ambient Temp.)/650 Degrees C, 1 210 MPa (at Ambient Temp.)/425 Degrees C, 1 210 MPa (at Ambient Temp.)/730 Degrees C, 1 550 Mpa (at Ambient Temp.)/235 Degrees C, 1 550 MPa (at Ambient Temp.)/425 Degrees C and 1 550 MPa (at Ambient Temp.)/600 Degrees C, – Dimensions | |
| ISO 9216 – Aerospace – Nuts, hexagonal, slotted (castellated), for pulleys, in alloy steel and cadmium plated or in corrosion-resistant steel and passivated – Dimensions and masses | |
| ISO 9217 – Aerospace – Washers, chamfered, with counterbore, for pulleys, in alloy steel and cadmium plated or in corrosion-resistant steel and passivated – Dimensions and masses | |
| ISO 9218 – Aerospace – Washers, flat, for pulleys, in alloy steel cadmium plated or in corrosion-resistant steel and passivated – Dimensions and masses | |
| ISO 9219 – Aerospace – Bolts, thin hexagonal head, for pulleys, close tolerance shank, short thread, in alloy steel and cadmium plated or in titanium alloy and MoS2 lubricated or in corrosion-resistant steel and passivated – Dimensions and masses | |
| ISO 9254 – Aerospace – Bolts, Normal Spine Head, Normal or Pitch Diameter Shank, Long Length MJ Threads, Metallic Material, Coated or Uncoated, Strength Classes Less Than or Equal to 1 100 MPa – Dimensions | |
| ISO 9255 – Aerospace — Bolts, normal spline head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions | |
| ISO 9256 – Aerospace – Bolts, Large Hexagonal Head, Normal or Pitch Diameter Shank, Long Length MJ Threads, Metallic Material, Coated or Uncoated, Strength Classes Less Than or Equal to 1 100 MPa – Dimensions | |
| ISO 9268 – Implants for Surgery – Metal Bone Screws with Conical Under-Surface of Head – Dimensions | |
| ISO 9609 – Aerospace – Nuts, hexagonal, plain, reduced height, normal across flats, with MJ threads, classifications: 450 MPa (at ambient temperature) /120 °C, 450 MPa (at ambient temperature) /235 °C, 600 MPa (at ambient temperature) /425 °C, 900 MPa (at ambient temperature) /235 °C, 900 MPa (at ambient temperature) /315 °C, 900 MPa (at ambient temperature) /650 °C, 1 100 MPa (at ambient temperature) /235 °C, 1 100 MPa (at ambient temperature) /730 °C and 1 250 MPa (at ambient temperature)/600 °C – Dimensions | |
| ISO 9618 – Aerospace – Nuts, hexagonal, slotted (castellated), reduced height, normal across flats, with MJ threads, classifications: 450 MPa (at ambient temperature)/120 °C, 450 MPa (at ambient temperature)/235 °C, 600 MPa (at ambient temperature)/ 425 °C, 900 MPa (at ambient temperature)/235 °C, 900 MPa (at ambient temperature)/315 °C, 900 MPa (at ambient temperature)/ 650 °C, 1 100 MPa (at ambient temperature)/235 °C, 1 100 MPa (at ambient temperature)/ 730 °C and 1 250 MPa (at ambient temperature)/600 °C – Dimensions | |
| ISO 9749 – Aerospace – Stud-Ends, in Corrosion-Resistant Steel, Swaged on Aircraft Control Wire Rope – Dimensions and Loads | |
| ISO 9974-1 – Connections for General Use and Fluid Power – Ports and Stud Ends with ISO 261 Threads with Elastomeric or Metal- to-Metal Sealing – Part 1: Threaded Ports | |
| ISO 9974-2 – Connections for General Use and Fluid Power – Ports and Stud Ends with ISO 261 Threads with Elastomeric or Metal- to-Metal Sealing – Part 2: Stud Ends with Elastomeric Sealing (Type E) | |
| ISO 9974-3 – Connections for General Use and Fluid Power – Ports and Stud Ends with ISO 261 Threads with Elastomeric or Metal- to-Metal Sealing – Part 3: Stud Ends with Metal-to-Metal Sealing (Type B) | |
| ISO 9974-4 – Connections for general use and fluid power – Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing – Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs | |
| ISO 10045 – Alpine skis – Binding mounting area – Requirements for test screws | |
| ISO 10096 – Aerospace – Nuts, Hexagonal, Slotted (Castellated), Red. Ht, Red. Across Flats, with MJ Threads | |
| ISO 10102 – Assembly tools for screws and nuts – Double-headed open-ended engineers’ wrenches – Outside dimensions | |
| ISO 10103 – Assembly tools for screws and nuts – Doubled-headed box wrenches, flat and offset – Outside dimensions and test torques | |
| ISO 10104 – Assembly tools for screws and nuts – Double-headed box wrenches, deep offset and modified offset – Outside dimensions | |
| ISO 10228 – Cross-country skis — Binding mounting area — Requirements for test screws | |
| ISO 10509 – Hexagon flange head tapping screws | |
| ISO 10510 – Tapping screw and washer assemblies with plain washers | |
| ISO 10511 – Prevailing torque type hexagon thin nuts (with non-metallic insert) | |
| ISO 10512 – Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread – Property classes 6, 8 and 10 | |
| ISO 10513 – Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread – Property classes 8, 10 and 12 | |
| ISO 10587 – Metallic and Other Inorganic Coatings – Test for Residual Embrittlement in both Metallic-Coated and Uncoated Externally-Threaded Articles and Rods – Inclined Wedge Method | |
| ISO 10597 – Road vehicles – Flat attachment fixing nuts for commercial vehicles – Test methods | |
| ISO 10642 – Fasteners — Hexagon socket countersunk head screws with reduced loadability | |
| ISO 10644 – Screw and washer assemblies made of steel with plain washers — Washer hardness classes 200 HV and 300 HV | |
| ISO 10663 – Hexagon nuts with flange, style 2 – Fine pitch thread | |
| ISO 10664 – Hexalobular internal driving feature for bolts and screws | |
| ISO 10664 – Hexalobular internal driving feature for bolts and screws | |
| ISO 10666 – Drilling Screws With Tapping Screw Thread – Mechanical and Functional Properties | |
| ISO 10669 – Plain Washers for Tapping Screw and Washer Assemblies – Normal and Large Series – Product Grade A | |
| ISO 10673 – Plain washers for screw and washer assemblies — Small, normal and large series — Product grade A | |
| ISO 10683 – Fasteners – Non-electrolytically applied zinc flake coating systems | |
| ISO 10684 – Fasteners — Hot dip galvanized coatings TECHNICAL CORRIGENDUM 1 | |
| ISO 10914 – Assembly Tools for Screws and Nuts – Sockets and Wrenches for Spline Drive | |
| ISO 10984-1 – Timber structures – Dowel-type fasteners – Part 1: Determination of yield moment | |
| ISO 10984-2 – Timber structures — Dowel-type fasteners — Part 2: Determination of embedding strength | |
| ISO 10984-2 – Timber structures — Dowel-type fasteners — Part 2: Determination of embedding strength | |
| ISO 11148-1 – Hand-held non-electric power tools — Safety requirements — Part 1: Assembly power tools for non-threaded mechanical fasteners | |
| ISO 11148-6 – Hand-held non-electric power tools – Safety requirements – Part 6: Assembly power tools for threaded fasteners | |
| ISO 11926-1 – Connections for General Use and Fluid Power – Ports and Stud Ends with ISO 725 Threads and O-Ring Sealing – Part 1: Ports with O-Ring Seal in Truncated Housing | |
| ISO 11926-2 – Connections for General Use and Fluid Power – Ports and Stud Ends with ISO 725 Threads and O-Ring Sealing – Part 2: Heavy-Duty (S Series) Stud Ends (SAE J 1926/2) | |
| ISO 11926-3 – Connections for General Use and Fluid Power – Ports and Stud Ends with ISO 725 Threads and O-Ring Sealing – Part 3: Light-Duty (L Series) Stud Ends | |
| ISO 12125 – Prevailing torque type hexagon nuts with flange (with non-metallic insert) with metric fine pitch thread, style 2 – Product grades A and B | |
| ISO 12126 – Prevailing torque type all-metal hexagon nuts with flange with metric fine pitch thread, style 2 – Product grades A and B | |
| ISO 12257 – Aerospace – Internal six-lobe drives – Metric series | |
| ISO 12258 – Aerospace – Bolts, Reduced Bihexagonal Head, Normal or Pitch Diameter Shank, Long Length MJ Threads, Metallic Material, Coated or Uncoated, Strength Classes Less Than or Equal to 1 275 MPa – Dimensions | |
| ISO 12260 – Aerospace – Screws, pan head, internal offset cruciform ribbed or unribbed drive, stepped shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa – Dimensions | |
| ISO 12261 – Aerospace – Screws, pan head, internal offset cruciform ribbed or unribbed drive, pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa – Dimensions | |
| ISO 12268 – Aerospace – Nuts, Hexagonal, Plain, Reduced Height, Reduced Across Flats, with MJ Threads, Cls: 450 MPa (at Ambient Temp.)/425 Degs C, 600 MPA (at Ambient Temp.)/235 Degs C, 600 MPa (at Ambient Temp.)/315 Degs C, 600 MPa (at Ambient Temp.)/650 Degs C, 900 MPa (at Ambient Temp.)/235 Degs C, 900 MPa (at Ambient Temp.)/730 Degs C and 1 100 MPa (at Ambient Temp.)/600 Degs C – Dimensions | |
| ISO 12272 – Aerospace – Nuts, Anchor, Self-Locking, Floating, Two Lug, with Incremental Counterbore, with MJ Threads, Classifications: 900 MPa (AT Ambient Temperature)/235 Degrees C, 900 MPa (AT Ambient Temperature)/315 Degrees C and 900 MPa (AT Ambient Temperature)/425 Degrees C – Dimensions | |
| ISO 12273 – Aerospace – Nuts, anchor, self-locking, floating, self-aligning, two lug, with MJ threads, classifications: 900 MPa (at ambient temperature)/235 °C, 900 MPa (at ambient temperature)/315 °C and 900 MPa (at ambient temperature)/425 °C – Dimensions | |
| ISO 12273 – Aerospace – Nuts, anchor, self-locking, floating, self-aligning, two lug, with MJ threads, classifications: 900 MPa (at ambient temperature)/235 °C, 900 MPa (at ambient temperature)/315 °C and 900 MPa (at ambient temperature)/425 °C – Dimensions | |
| ISO 12274 – Aerospace – Nuts, Anchor, Self-Locking, Floating, Self-Aligning, Single Lug, with MJ Threads, Classifications: 900 MPa (at Ambient Temperature/235 Degrees Celsius, 900 MPa (at Ambient Temperature)315 Degrees Celsius and 900 MPa (at Ambient Temperature)425 Degrees Celsius – Dimensions | |
| ISO 12278 – Aerospace – Nuts, Barrel, Self-Locking, Floating, Self-Aligning, with MJ Threads, Classifications: 900 MPa (at Ambient Temperature)/235 Degrees C, 1 100 MPa (at Ambient Temperature)/235 Degrees C, 1 250 MPa (at Ambient Temperature)/235 Degrees C and 1 550 MPa (at Ambient Temperature)/235 Degrees C – Dimensions | |
| ISO 12280 – Aerospace – Retainers, Spring, Sheet Metal, for Self-Locking Barrel Nuts – Dimensions | |
| ISO 12474 – Hexagon socket head cap screws with metric fine pitch thread | |
| ISO 12777-1 – METHODS OF TEST FOR PALLET JOINTS – PART 1: DETERMINATION OF BENDING RESISTANCE OF PALLET NAILS, OTHER DOWEL-TYPE FASTENERS AND STAPLES | |
| ISO 13415 – Aerospace – Airframe Needle Track Roller, Stud Type, Single-Row, Sealed – Inch Series | |
| ISO 13417 – Aerospace – Airframe Needle Track Roller, Stud Type, Single-Row, Sealed – Metric Series | |
| ISO 13469 – Mechanical joining – Form-fit blind rivets and (lock) bolt joints – Specifications and qualification of testing procedures | |
| ISO 13589 – Aerospace – Nuts, Bihexagonal, Self-Locking, with Counterbore and MJ Threads, Classifications: 1 100 MPa (at Ambient Temp)/425 Deg C, 1 100 MPa (at Ambient Temp)/650 Deg C, 1 210 MPa (at Ambient Temp)/425 Deg C, 1 210 MPa (at Ambient Temp)/730 Deg C, 1 550 MPa (at Ambient Temp)/235 Deg C, 1 550 MPa (at Ambient Temp)/425 Deg C and 1 550 MPa (at Ambient Temp)/600 Deg C – Dimensions | |
| ISO 13921 – Aerospace — Screws, 100 degrees reduced countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions | |
| ISO 14579 – Hexalobular socket head cap screws | |
| ISO 14580 – Hexalobular socket cheese head screws | |
| ISO 14581 – Fasteners – Hexalobular socket countersunk flat head screws | |
| ISO 14582 – Fasteners – Hexalobular socket countersunk head screws, high head | |
| ISO 14582 – Fasteners – Hexalobular socket countersunk head screws, high head | |
| ISO 14583 – Hexalobular socket pan head screws | |
| ISO 14584 – Hexalobular socket raised countersunk head screws | |
| ISO 14585 – Hexalobular socket pan head tapping screws | |
| ISO 14586 – Hexalobular socket countersunk head tapping screws | |
| ISO 14587 – Hexalobular socket raised countersunk (oval) head tapping screws | |
| ISO 14713-1 – Zinc coatings – Guidelines and recommendations for the protection against corrosion of iron and steel in structures – Part 1: General principles of design and corrosion resistance | |
| ISO 14713-3 – Zinc coatings – Guidelines and recommendations for the protection against corrosion of iron and steel in structures – Part 3: Sherardizing | |
| ISO 14955-4 – Machine tools – Environmental evaluation of machine tools – Part 4: Principles for measuring metalforming machine tools and laser processing machine tools with respect to energy efficiency | |
| ISO 15065 – Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 | |
| ISO 15071 – Hexagon bolts with flange — Small series — Product grade A | |
| ISO 15072 – Hexagon bolts with flange with metric fine pitch thread – Small series – Product grade A | |
| ISO 15330 – Fasteners – Preloading Test for the Detection of Hydrogen Embrittlement – Parallel Bearing Surface Method | |
| ISO 15480 – Fasteners — Hexagon washer head drilling screws with tapping screw thread | |
| ISO 15481 – Cross Recessed Pan Head Drilling Screws with Tapping Screw Thread | |
| ISO 15482 – Cross Recessed Countersunk Head Drilling Screws with Tapping Screw Thread | |
| ISO 15483 – Cross Recessed Raised Countersunk Head Drilling Screws with Tapping Screw Thread | |
| ISO 15488 – Collets with 8° setting angle for tool shanks Collets, nuts and fitting dimensions | |
| ISO 16047 – FASTENERS – TORQUE/CLAMP FORCE TESTING | |
| ISO 16048 – Passivation of Corrosion-Resistant Stainless-Steel Fasteners | |
| ISO 16130 – Aerospace series – Dynamic testing of the locking behaviour of bolted connections under transverse loading conditions (vibration test) | |
| ISO 16228 – Fasteners – Types of inspection documents | |
| ISO 16239 – Metric series wires for measuring screw threads | |
| ISO 16426 – Fasteners Quality assurance system | |
| ISO 16528-1 – Boilers and pressure vessels — Part 1: Performance requirements | |
| ISO 16573 – Steel – Measurement method for the evaluation of hydrogen embrittlement resistance of high strength steels | |
| ISO 16573-1 – Steel — Measurement method for the evaluation of hydrogen embrittlement resistance of high strength steels — Part 1: Constant load test | |
| ISO 16670 – Timber structures Joints made with mechanical fasteners Quasi-static reversed-cyclic test method | |
| ISO 17754 – Timber structures – Test methods – Torsional resistance of driving in screws | |
| ISO 19023 – Dentistry – Orthodontic anchor screws | |
| ISO 21670 – Fasteners – Hexagon weld nuts with flange | |
| ISO 21982 – Assembly tools for screws and nuts — Ratcheting wrenches — Technical requirements | |
| ISO 22074-3 – Railway infrastructure — Rail fastening systems — Part 3: Proof load test method for pull-out resistance | |
| ISO 22437 – Aerospace series – Pipe coupling 8°30’ in titanium alloy – Nut for welded ferrule | |
| ISO 27528 – Wood-based panels — Determination of resistance to axial withdrawal of screws | |
| ISO DIS 2236 – ASSEMBLY TOOLS FOR SCREWS AND NUTS – FORGED AND TUBULAR SOCKET WRENCHES – MAXIMUM OUTSIDE HEAD DIMENSIONS | |
| ISO DIS 2702 – Fasteners – Heat-treated self-tapping screws – Mechanical and physical properties | |
| ISO DIS 3506-5 – Fasteners – Mechanical properties of corrosion-resistant stainless steel fasteners – Part 5: Special fasteners (also including fasteners from nickel alloys) for high temperature applications | |
| ISO DIS 898-6 – Mechanical properties of fasteners made of carbon steel and alloy steel — Part 6: Nuts with specified proof load values — Fine pitch thread | |
| ISO DIS 4014 – Hexagon head bolts — Product grades A and B | |
| ISO DIS 4015 – Hexagon head bolts with reduced shank (shank diameter ≈ pitch diameter) — Product grade B | |
| ISO DIS 4016 – Hexagon head bolts — Product grade C | |
| ISO DIS 4017 – Hexagon head screws — Product grades A and B | |
| ISO DIS 4018 – Hexagon head screws — Product grade C | |
| ISO DIS 4032 – Hexagon regular nuts (style 1) – Product grades A and B | |
| ISO DIS 4033 – Hexagon high nuts (style 2) – Product grades A and B | |
| ISO DIS 4034 – Hexagon regular nuts (style 1) – Product grade C | |
| ISO DIS 4035 – Hexagon thin nuts (style 0), chamfered – Product grades A and B | |
| ISO DIS 4042 – Fasteners — Electroplated coating systems | |
| ISO DIS 4161 – Hexagon high nuts with flange – Product grades A and B | |
| ISO DIS 4579 – Aerospace — Drives, internal, TORX PARALOBE drive — Geometrical definition, gaging and technical requirements | |
| ISO DIS 4580 – Aerospace — Internal drive, TORX PARALOBE, driver bit — Geometrical definition, gaging and technical requirements | |
| ISO DIS 7040 – Prevailing torque hexagon regular nuts (with non-metallic insert) – Product grades A and B | |
| ISO DIS 7041 – Prevailing torque hexagon high nuts (with non-metallic insert) – Product grades A and B | |
| ISO DIS 7042 – Prevailing torque (all-metal) hexagon high nuts – Product grades A and B | |
| ISO DIS 7043 – Prevailing torque type hexagon nuts with flange (with non-metallic insert), style 2 – Product grades A and B | |
| ISO DIS 7044 – Prevailing torque (all-metal) hexagon high nuts with flange – Product grades A and B | |
| ISO DIS 7689 – Aerospace — Bolts, with MJ threads, made of alloy steel, strength class 1 100 MPa — Procurement specification | |
| ISO DIS 7719 – Prevailing torque (all-metal) hexagon regular nuts – Product grades A and B | |
| ISO DIS 8673 – Hexagon regular nuts (style 1), with fine pitch thread – Product grades A and B | |
| ISO DIS 8674 – Hexagon high nuts (style 2), with fine pitch thread – Product grades A and B | |
| ISO DIS 8675 – Hexagon thin nuts (style 0) chamfered, with fine pitch thread – Product grades A and B | |
| ISO DIS 8676 – Hexagon head screws with metric fine pitch thread — Product grades A and B | |
| ISO DIS 8765 – Hexagon head bolts with metric fine pitch thread — Product grades A and B | |
| ISO DIS 10484 – Fasteners – Widening test on nuts | |
| ISO DIS 10511 – Prevailing torque hexagon thin nuts (with non-metallic insert) – Product grades A and B | |
| ISO DIS 10512 – Prevailing torque hexagon regular nuts (with non-metallic insert), with fine pitch thread – Product grades A and B | |
| ISO DIS 10513 – Prevailing torque (all-metal) hexagon high nuts, with fine pitch thread – Product grades A and B | |
| ISO DIS 10663 – Hexagon high nuts with flange, with fine pitch thread – Product grades A and B | |
| ISO DIS 11926-1 – CONNECTIONS FOR GENERAL USE AND FLUID POWER – PORTS AND STUD ENDS WITH ISO 263 UN AND UNF THREADS AND O-RING SEALING – PART 1: PORTS WITH TRUNCATED HOUSING FOR O-RING SEAL | |
| ISO DIS 11926-2 – CONNECTIONS FOR GENERAL USE AND FLUID POWER – PORTS AND STUD ENDS WITH ISO 263 INCH THREADS AND O-RING SEALING – PART 2: HEAVY-DUTY (S SERIES) STUD ENDS | |
| ISO DIS 11926-3 – CONNECTIONS FOR GENERAL USE AND FLUID POWER – PORTS AND STUD ENDS WITH ISO 263 INCH THREADS AND O-RING SEALING – PART 3: LIGHT-DUTY (L SERIES) STUD ENDS | |
| ISO DIS 12125 – Prevailing torque hexagon high nuts with flange (with non-metallic insert), with fine pitch thread – Product grades A and B | |
| ISO DIS 12126 – Prevailing torque (all-metal) hexagon high nuts with flange, with fine pitch thread – Product grades A and B | |
| ISO DIS 23887 – AEROSPACE – BLIND FASTENERS, THREADED TYPE, SELF-LOCKING – TEST METHOD FOR LOCKING TORQUE | |
| ISO DIS 24200 – Petroleum, petrochemical and natural gas industries — Bulk material for offshore projects — Pipe support | |
| ISO DIS 24567 – Aerospace series — Pipe coupling 8°30′ in titanium alloy — Thrust wire nuts | |
| ISO FDIS 3408-2 – BALL SCREWS – PART 2: NOMINAL DIAMETERS AND NOMINAL LEADS – METRIC SERIES | |
| ISO FDIS 965-3 – ISO general purpose metric screw threads — Tolerances — Part 3: Limit deviations for screw threads | |
| ISO FDIS 965-4 – ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing | |
| ISO TR 16224 – Technical aspects of nut design | |
| ISO TR 17104 – Rotary tool for threaded fasteners Hydraulic impulse tools Performance test method | |
| ISO TR 20491 – Fasteners — Fundamentals of hydrogen embrittlement in steel fasteners |
